PROE如何出工程图

PROE工程图配置文件及pro/E中绘图配置文件.dtl的通常设置与解释

很多人不懂设置PRO/E工程图配置文件，总觉得在PRO/E中出工程图非常别扭，图面也不好整理等等的原因，我以前也不懂，也是将Pro/E的工程图 转到CAD里面再标注，浪费时间。如果产品尺寸有改动，就又要转一次，又重新标注尺寸等等，但现在我一直是在PRO/E中出工程图，高效、快速，由于PRO/E的文件关联性，产品只要有改到，工程图也就相应的更改，非常方便。 将配置文件里的内容按一下重新设置即可：

drawing_text_height 3 text_thickness 0.1 text_width_factor 0.800000 broken_view_offset 1.000000 create_area_unfold_segmented YES def_view_text_height 3 def_view_text_thickness 0.1 detail_circle_line_style SOLIDFONT detail_circle_note_text DEFAULT detail_view_circle ON half_view_line SOLID

model_display_for_new_views no_hidden projection_type first_angle show_total_unfold_seam YES

tan_edge_display_for_new_views DEFAULT view_note STD_ISO view_scale_denominator 0 view_scale_format ratio_colon detail_view_boundary_type CIRCLE detail_view_scale_factor 2.000000 crossec_arrow_length 5

crossec_arrow_style TAIL_ONLINE crossec_arrow_width 2.0

crossec_text_place AFTER_HEAD crossec_type OLD_STYLE cutting_line std_iso cutting_line_adapt NO

cutting_line_segment 0.000000 def_xhatch_break_around_text NO def_xhatch_break_margin_size 0.150000 draw_cosms_in_area_xsec NO remove_cosms_from_xsecs TOTAL

show_quilts_in_total_xsecs NO datum_point_shape CROSS datum_point_size 8

hidden_tangent_edges DEFAULT hlr_for_datum_curves YES hlr_for_pipe_solid_cl NO hlr_for_threads YES location_radius DEFAULT(2.) mesh_surface_lines ON ref_des_display NO

show_sym_of_suppressed_weld NO thread_standard std_iso weld_light_xsec NO weld_solid_xsec NO allow_3d_dimensions yes

angdim_text_orientation parallel_outside associative_dimensioning YES blank_zero_tolerance NO

chamfer_45deg_leader_style std_iso chamfer_45deg_dim_text JIS clip_diam_dimensions YES

clip_dimensions YES

clip_dim_arrow_style DOUBLE_ARROW default_dim_elbows YES dim_fraction_format DEFAULT dim_leader_length 5 dim_text_gap 0.5 display_tol_by_1000 NO draft_scale 1.000000 draw_ang_units ANG_DEG draw_ang_unit_trail_zeros no dual_digits_diff -1 dual_dimensioning NO dual_dimension_brackets YES dual_metric_dim_show_fractions NO dual_secondary_units MM iso_ordinate_delta yes

lead_trail_zeros STD_DEFAULT lead_trail_zeros_scope DIMS orddim_text_orientation horizontal ord_dim_standard STD_ANSI parallel_dim_placement ABOVE

radial_dimension_display STD_ASME shrinkage_value_display percent_shrink symmetric_tol_display_standard STD_ASME text_orientation parallel_diam_horiz tol_display NO

tol_text_height_factor 0.4 tol_text_width_factor STANDARD use_major_units yes witness_line_delta 1 witness_line_offset 0.5 default_font font

dim_dot_box_style DEFAULT draw_arrow_length 3 draw_arrow_style filled draw_arrow_width 1.5

draw_attach_sym_height DEFAULT draw_attach_sym_width DEFAULT draw_dot_diameter DEFAULT leader_elbow_length 5

leader_extension_font SOLIDFONT axis_interior_clipping yes

axis_line_offset 3 circle_axis_offset 3

radial_pattern_axis_circle yes

asme_dtm_on_dia_dim_gtol ON_GTOL gtol_datums std_iso

gtol_datum_placement_default ON_BOTTOM gtol_dim_placement ON_BOTTOM gtol_symbols_same_size NO new_iso_set_datums YES stacked_gtol_align NO 2d_region_columns_fit_text NO all_holes_in_hole_table YES dash_supp_dims_in_region YES def_bom_balloons_attachment EDGE def_bom_balloons_snap_lines NO def_bom_balloons_stagger NO

def_bom_balloons_stagger_value 0.600000 def_bom_balloons_view_offset 0.800000 def_bom_balloons_edge_att_sym ARROWHEAD def_bom_balloons_surf_att_sym INTEGRAL min_dist_between_bom_balloons 0.800000

model_digits_in_region no

reference_bom_balloon_text \"DEFAULT\" show_cbl_term_in_region YES sort_method_in_region DELIMITED zero_quantity_cell_format EMPTY draw_layer_overrides_model NO ignore_model_layer_status YES model_grid_balloon_display YES model_grid_balloon_size 4.0 model_grid_neg_prefix - model_grid_num_dig_display 0 model_grid_offset DEFAULT

model_grid_text_orientation HORIZONTAL model_grid_text_position CENTERED pipe_pt_line_style DEFAULT pipe_pt_shape CROSS pipe_pt_size DEFAULT

show_pipe_theor_cl_pts BEND_CL

decimal_marker COMMA_FOR_METRIC_DUAL default_pipe_bend_note NO drawing_units mm

harn_tang_line_display NO line_style_standard std_ansi max_balloon_radius 0 min_balloon_radius 0 node_radius DEFAULT pos_loc_format %s%x%y, %r sym_flip_rotated_text NO weld_symbol_standard std_iso

yes_no_parameter_display TRUE_FALSE

设置完后注意保存，以后使用直接调用此工程图配置文件。